In KB "Panorama" the "Workstation of cadastral engineer" version 14.3.2 has been developed. The new version provides creation of a report on the correction of a registry error based on the results of determining the coordinates of the characteristic points of the boundaries and the area of land plots, the contours of buildings, constructions, objects under construction, the boundaries of municipalities, settlements, territorial zones, forestries.

The report is formed in accordance with the Procedure for changing in the Unified State Register of Real Estate of information about location of the boundaries of the land plot when correcting a registry error, approved by order of Rosreestr dated 01.06.2021 No. P/0241. According to paragraph 9, based on the results of determining the coordinates, the Federal State Budgetary Institution "FKP Rosreestr" (its branches) prepare a Report in electronic form.

For forming the Report, a new mode "Correction of registry errors" has been developed. It provides in an automatic mode the Report creation by a template and filling of fields with the data. The program reads from the cadastral map the coordinates of the characteristic points of the boundaries of cadastral objects contained in the EGRN and new coordinates determined by the authorized organization and proposed for correction of a registry error. According to the coordinates offered for correction of a registry error, the area of land plots is calculated. The value of the calculated area is compared with the area of the object specified in the EGRN. The percent of discrepancy between the values and the size of the error in determining the area are inserted into the Report. Also, when forming the Report, information about the method of determining the coordinates and the root mean square error is entered simultaneously in relation to all points of the object boundary.

At automatic filling the Report the cadastral map is used created according to the digital classifier survey.v6.rscz, with using the objects of layer "Correction of registry errors". Onto a map the boundaries of cadastral objects should be put according to the coordinates contained in the EGRN and the new boundaries of cadastral objects,determined by an authorized organization and offered for correction of a registry error. For identification of cadastral objects and an establishing a conformity of boundaries of the objects recorded in the Unified State Register of Real Estate and defined for correction of a registry error, cadastral numbers of objects of real estate and registry numbers of objects boundaries of the registry of boundaries are used. The procedure for preparing a cadastral map is described in the documentation and electronic help for the program.

The current version of the program is available for download in the Download section.

Specialists of KB "Panorama" have prepared a video lesson on the description of the functionality of the software package "Workstation of cadastral engineer". The product is supplied in two versions: "Workstation of cadastral engineer" or "Workstation of cadastral engineer Pro". From the training material, users learn about the distinctive features of each of the variants of the software product.

Automated workstation of a cadastral engineer (ARM CI) is a software package for performing the entire cycle of cadastral work: from requesting information from the Unified State Real Estate Register to generating a package of documents for state cadastral registration. The program supports the creation of both electronic and printed versions of land survey, technical plans, a map (plan) of a land management object, scheme of arrangement of a land plot on the cadastral plan of the territory and other documents necessary for cadastral registration and land management.

"Workstation of cadastral engineer Pro" includes all the functionality of "Workstation of cadastral engineer", as well as tasks for creating and printing floor plans, office processing of the results of field geodetic measurements, solving direct and return geodetic tasks and the task of automatically creating objects by information already available on a map.

You can get acquainted with the training materials in the "Video lessons" section.

Specialists of KB "Panorama" prepared and placed the maps of the Belgorod and Rostov regions on the geoportal "Bank of spatial data". The maps were formed using OpenStreetMap data, source data was obtained from Geofabrik website. To work with the maps, you can use the GIS Panorama Mini program or other software products of KB "Panorama".

The maps were led to the modernised classifier of large-scale plans of scale 1: 5 000 (map5000m) and were saved into a packed project (mptz). Publishing of updates in bank of spatial data is made by using the program of Databank of digital maps and remote sensing data. Publishing contents of bank of spatial data on the geoportal and data access for downloading are implemented by means of GIS WebServer SE.

Free maps on the basis of OpenStreetMap data are available for download on the page "Digital maps".

In KB "Panorama" the GIS "Panorama" version 14.3.2 has been developed. The new version expands the GIS capabilities for the creating, updating and analyzing digital terrain models by including into the software of scripts in Python language that can be written in any text editor. The tools for building reports, three-dimensional modeling, creating and controlling the quality of digital terrain maps, and processing multispectral images have been improved.

In "Run applications" dialog the "Scripts" bookmark for executing scripts in the Python language has been added. The "Basic set of scripts" node is initially installed in the script tree, which contains scripts supplied with the GIS. To connect user scripts, you can create your own nodes (themes) for their grouping. The basic set of scripts demonstrates the execution of various procedures for processing the coordinates and attributes of vector map objects, solving the computational problems, converting data and other tasks.

When writing scripts, several thousand GIS core functions (MAPAPI) are available. Function prototypes are declared as imported Python scripts from the Users\Public\Documents\Panorama\py_mapi14 folder. The procedure for applying MAPAPI functions described in the document "Application tasks. Development of new modules" will also be valid for Python scripts. For proper processing of script strings containing national characters (Russian, Chinese, Spanish, and so on), scripts must be UTF-8 encoded.

The function called from the script can perform some action on the selected object or on selected objects if the user has selected some objects on the map. To enter additional data processing parameters, both GIS dialogs and dialogs written on the basis of the standard tkinter component can be called. Scripts can indicate the progress of data processing by indicating the name of the processing stage, the percentage of execution, the number of processed and selected objects, the elapsed and remaining processing time. Based on the results of the analysis and processing of vector map objects, some objects can be selected that can be marked on the map as a result of working the script and/or for further processing in the chain of executed scripts or by interactive GIS tools.

In the Run applications dialog, you can select a program from the user's existing ones (from a text editor to a professional script editor) to create, view and edit Python scripts from the script tree. To execute scripts, you must first download and install the Python interpreter. The basic set of scripts has been developed and tested based on Python version 3.7.9 on MS Windows 7 and higher, and version 3.10.5 on MS Windows 10. The base scripts are located in a shared folder like: \Users\Public\Documents\Panorama\py_base14 .

The "Reports designer" task has been improved. In the object geometry editing mode, the functions of deleting objects, interactively changing the height of the signature font, adding and deleting borders for insets have been added. There are added a display of the background grid and setting its parameters: display, color, view, position on the map, the ability to disable when exporting a report to graphic files, permission to stick the cursor to grid nodes when creating and editing objects. In the insertion mode, the ability to stick the cursor to grid nodes has been added, the ability to interrupt an unfinished operation has been added. In the object geometry editing mode, the function of binding all points of object to grid nodes has been added. Grouping of buttons has been made. Rarely used modes are designed into group buttons with the ability to select a specific mode through the menu. When saving stamps, the ability to decode objects (from an object with a classifier code into a graphic object) has been added, which allows you later to load this stamp into a map with any classifier. In interactive modes the hints in the info line have been added.

In the "Complex of urban tasks", the dialog "Building the areas of acceptable placement of objects" has been updated. The mode provides automated construction of the minimum offset line from the boundaries of the land plot, within which the construction of capital construction objects and the zone of the planned placement of the capital construction object is permitted. The constructions are carried out in accordance with the requirements for the town-planning plan of the land plot established by the "Town-planning code of the Russian Federation" dated 29.12.2004 N 190-FZ as amended on 01.05.2022. Information about restrictions on the use of the land plot is used for construction, including if the land plot is fully or partially located within the boundaries of zones with special conditions for the use of territories, has public easements and intersects with red lines.

In the "Navigator 3D" task, the "Scenario of moving objects" mode has been improved. When displaying a scenario, it is possible to display a given movement trajectory and inversion trace or the passed trajectory of individual objects. In the "Scenario setup" dialog, the ability to set a three-dimensional view for the trajectory and trace is added, not only by default, but also with a choice from the scenario classifier. The user can create his own special linear objects of trajectories in the classifier and set the required three-dimensional view for them. This approach improves the view of the displayed scenario and the recognition of moving objects when modeling movements.

Into the group of applications "Automatic creation of objects" a new application "Creating a map of minimum heights" has been added. The procedure serves as an addition to the Complex of documents preparation of aeronautical information and is intended for automatic creating a map of minimum heights (AMA) based on of matrixes of heights of a relief and maps of obstacles. Calculations are performed in accordance with Doc 8168 ICAO Rules - Aircraft Operations - Volume II. The map of minimum heights is a matrix of signatures for the values of minimally allowable heights of flight in established conventional signs with a given size of the analyzed cells on the ground. Heights labels are drawn up in accordance with the requirements of Doc 8697 ICAO Manual for Aeronautical Charts.

The task "Correction of object metrics" has been improved. In the "Break down objects onto component parts" mode, the ability to process multipoint objects with subobjects has been added. This allows you to break the point objects onto a group of independent objects, consisting of sub-objects, each of which, in turn, contains several points.

The task "Map Legend" has been improved. On the "Maps", "Rasters", "Matrixes", "Models" bookmarks, an information sign "(!)" is set if the coordinate system of the added data does not match the current coordinate system of the main document. On the "Maps" bookmark, an updating the content of the classifier tree has been improved when changing the contents of vector map objects. For example, if the filter "Objects available on the map" is set in the "Map legend", when an object is placed onto the map that is not part of the tree, the legend will be automatically rebuilt. In the "Map Legend" and "Data List" tasks, the updating of visibility of maps, rasters, matrixes and geoportals is synchronized.

Control of absolute heights has been improved. Support for national maps and classifiers was added that have contour lines of different types with the same external code. This allows you to control the correctness of the formation of contour lines, both for classifiers containing separate series of objects for different types of contour lines: Thick horizontals, Thick horizontals on glaciers, Thick horizontals on rocks; Main contours and so on, and classifiers with one code (series) for all types of contour lines - in this case, control of contour heights is customized and performed by object keys.

For multispectral rasters imported in the "Do not copy the input image to RSW file" mode, support for channel color depth of 32 and 64 bits has been added. To convert the color to 8 bits, the minimum and maximum values determined by the reduced image are used during display. Single-channel rasters with real pixel encoding, which are usually used to store matrix height data, are displayed in grayscale.

The "Latest commands" item has been added into the right-click menu, which contains a list of the latest executed commands in various tasks and the executed applications from the "Run applications" dialog. A combination of the Shift key and the right mouse button is used for immediately calling a list of latest commands.

The "Selection by an arbitrary area" mode has been improved. Added automatic launch of the mode with the following combinations: drawing points in the form of a polygon by pressing the middle mouse button (MBM); pressing Shift and MMB - in the form of a rectangular area; outline the selected area by holding down MMB.

The new version of the program is available for download in the Download section.

Specialists of KB "Panorama" have tested for compatibility of the software the Geoinformation system "Operator" for power structures (GIS Operator SE), Geoinformation system "Panorama х64", GIS Panorama Mini with OSON "OSnova". During tests, there were confirmed the compatibility and correctness of working the software the GIS Operator SE, GIS "Panorama", GIS "Panorama Mini" and OSON "OSnova".

GIS Operator SE - universal domestic geoinformation system for power structures. The program is designed for accumulation, storage, the automated processing and display of data, calculation results and forecasts with geospatial reference. GIS Operator SE contains tools of displaying and processing vector, raster and matrix maps. The application provides users with tools for solving specialized tasks of modeling the movement of special objects against the background of 3D model, forecasting of consequences of emergencies at hazardous objects, monitoring of aircraft movement, conducting of geodetic and topographic work, processing the data from GPS/GLONASS navigation devices, printing the displayed spatial data to various output devices and many others.

GIS Operator SE is certified according to the 2nd level of control of the absence of undeclared capabilities in the Ministry of Defense of the Russian Federation, it is included in the Unified register of Russian programs for electronic computers and databases (registry entry No.10628 of 05/27/2021).

GIS "Panorama" is the universal geographic information system that has tools for creating and editing digital maps and city plans, processing remote sensing data, performing various measurements and calculations, overlay operations, building 3D models, processing raster data, tools of preparing graphic documents in digital and printed form, as well as tools for working with databases. GIS is used for mapping, land management and cadastre, geodetic surveys, and the creation of geoportals. The GIS is included in the Unified register of Russian programs for electronic computers and databases (registry entry No.4227 dated March 29, 2018).

GIS "Panorama Mini" is the universal geoinformation system designed to collect spatial data, maintain a database of spatial data, create and update digital maps and plans, and create information systems for various purposes. The GIS is included in the Unified register of Russian programs for electronic computers and databases (registry entry No.7226 dated 11/03/2020).

OSON "OSnova" is a general-purpose Operating system designed to build secure automated systems that process confidential information and personal data. Developer JSC "NPPKT". OSON "OSnova": Certificate of state registration of the computer program No. 2018616118 dated 05/23/2018. It is included in the Unified register of Russian programs for electronic computers and databases (registry entry No. 5913 dated November 19, 2019). Certificate of Conformity of the FSTEC of Russia No. 4381 for compliance with the information security requirements established in the documents "Information security requirements that establish levels of trust in technical information security tools and information technology security tools" (FSTEC of Russia, 2020) - for the 4th level of trust, "Information security requirements for operating systems" (FSTEC of Russia, 2016), "Profile of protection of operating systems type A of the fourth protection class IT.OS.A4.PZ" (FSTEC of Russia, 2017).